 |
 |
 |
|
Rapid-Recovery Heating for High-Throughput Batch Production
The PRIMO 50 Rapid-Cycle Industrial Melter is engineered for production environments where material is loaded repeatedly and recovery between loads can determine daily output.
Capacity / Dimensions / Power
Production Capacity With Rapid-Recovery Heating
Approximate wax capacity is 56 lb (25 kg) in a 7 gal (26 L) vessel. Inner dimensions are 15" diameter × 10" deep; overall dimensions are approximately 17" L × 17" W × 12" H. Installed Rapid-Cycle heating power is 1,550 W, the same as the corresponding PRIMO X-Treme configuration.
When Recovery Time Controls Production
Built Around the Next Load, Not Just the First Melt
Rapid-Cycle is intended for operations where filling, transfer, coating, casting, pumping or another downstream process is waiting for material to recover toward the required operating temperature after new material is added.
Repeated LoadingNew material is introduced throughout the production day. Recovery Is a BottleneckThermal recovery is consuming meaningful production time. Throughput Has a TargetOutput can be defined by pounds per cycle, recovery minutes or batches per shift.
Repeated Batch Production
Load → Recover → Process → Reload
Rapid-Cycle is designed around repeated production loading. Actual recovery depends on material, batch size, feed temperature, target temperature, operating level, ambient conditions, agitation, recirculation and operator procedure.
Required Recovery Target
Size the System Around the Production Requirement
Provide the pounds added per cycle, starting temperature, operating temperature, desired recovery time and production demand per shift. These are the variables used to determine whether this Rapid-Cycle model is appropriately sized.
Material Compatibility
Higher Recovery Capability Must Match the Material
Rapid-Cycle is intended for waxes and compatible industrial materials that can tolerate the selected heat-transfer rate. Heat-sensitive formulations or materials prone to scorching, separation, skin formation or localized buildup should be reviewed before selecting Rapid-Cycle.
Standard Equipment & Options
Configure the System Around the Process
Standard Foundation304 stainless steel vessel, #4 interior finish, insulated double-wall construction, stainless lid, digital material-temperature control and PRIMO waterless heating. Process OptionsAgitation, recirculation, filtration, outlet configuration, heated valves, pumps, hoses and filling integration as required. CleanabilityEnhanced smooth-ground interior welds, washdown-related construction and application-specific options where required.
Throughput Data Needed
Information Needed for Rapid-Cycle Sizing
- Material or formulation
- Pounds introduced per cycle
- Starting material temperature
- Required operating temperature
- Desired recovery time
- Batches or pounds required per shift
- Available voltage, phase and amperage
- Agitation, recirculation, transfer or filling requirements
✓
Factory Tested Before ShipmentEach PRIMO system is inspected and function-tested prior to professional packaging and shipment.
Compare PRIMO Families
Standard PRIMOGeneral melting, heating and production holding. Thermal ConditioningControlled heating and extended material-temperature stability. Rapid-CycleRepeated loading, shorter compatible recovery cycles and throughput.
Request a Rapid-Cycle Application Review
Cleaning Your MelterClean it like a high end stainless steel cooking pot. Wipe it out with a cloth. For soap and food products, soap and water works fine. If something has burned on, a scouring pad takes care of it. Round tank, no corners to clean.
PRIMO 50 Rapid-Cycle Industrial Melter
56 lb (25 kg)Approximate wax capacity
7 gal (26 L)Physical vessel capacity
15" diameter × 10" deepInner dimensions / I.D.
1,550 WInstalled Rapid-Cycle power
|
Vessel & Construction
|
|
Product-Contact Material
|
304 stainless steel
|
|
Interior Finish
|
#4 stainless finish
|
|
I.D. / Inner Dimensions
|
15" diameter × 10" deep
|
|
O.D. / Overall Dimensions
|
17" L × 17" W × 12" H
|
|
Construction
|
Double-wall insulated stainless steel
|
|
Installed Heating Power
|
1,550 W
|
|
Controller
|
Digital material-temperature controller
|
|
Material Load per Cycle
|
Application-specific
|
|
Recovery Target Used for Sizing
|
Application-specific
|
|
Minimum Operating Material Level
|
Per approved application and operating instructions
|
|
Agitation / Recirculation
|
Application-specific
|
|
Outlet
|
Configured at purchase to match the process
|
|
Shipping Weight
|
Confirm with final configured system
|
Production Planning
How the PRIMO 50 Rapid-Cycle Fits Into Production
Use this model where approximately 56 lb (25 kg) of wax capacity, 7 gal (26 L) of vessel volume and 1,550 W of X-Treme-equivalent installed heating power fit the required batch size and recovery objective.
Mix & ConditionAdd agitation or recirculation where material behavior requires it. Filter & TransferIntegrate pumps, filtration, heated hoses and valves around actual viscosity and flow requirement. Dispense & FillSupply downstream filling or process equipment from the heated vessel.
Physical Planning
Confirm Footprint, Access and Utilities
DimensionsInner: 15" diameter × 10" deep
Outer: 17" L × 17" W × 12" H Before InstallationConfirm operator access, loading method, outlet height, downstream-equipment location, voltage, phase and amperage.
|
|
|
 |
|
 |
|
